? semiconductor components industries, llc, 2015 january, 2015 ? rev. 10 1 publication order number: MC74AC00/d MC74AC00, mc74act00 quad 2-input nand gate high?performance silicon?gate cmos features ? output drive capability: 24 ma ? operating voltage range: 2 to 6 v ac00; 4.5 to 5.5 act00 ? low input current: 1.0 a ? high noise immunity characteristic of cmos devices ? in compliance with the jedec standard no. 7a requirements ? chip complexity: 32 fets ? these are pb?free devices 3 y1 1 a1 pin 14 = v cc pin 7 = gnd figure 1. logic diagram 2 b1 6 y2 4 a2 5 b2 8 y3 9 a3 10 b3 11 y4 12 a4 13 b4 y = ab figure 2. pinout: 14?lead packages (top view) 13 14 12 11 10 9 8 2 1 34567 v cc b4 a4 y4 b3 a3 y3 a1 b1 y1 a2 b2 y2 gnd marking diagrams xxx = ac or act a = assembly location wl or l = wafer lot y = year ww or w = work week g or = pb?free package tssop?14 dt suffix case 948g xxx 00 alyw 1 14 soic?14 d suffix case 751a 1 14 1 14 see detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. ordering information l l h h l h l h function table inputs output ab h h h l y www. onsemi.com xxx00g awlyww 1 14 (note: microdot may be in either location)
MC74AC00, mc74act00 www. onsemi.com 2 maximum ratings symbol parameter value unit v cc dc supply voltage 0.5 to 7.0 v v i dc input voltage 0.5 v i v cc 0.5 v v o dc output voltage (note 1) 0.5 v o v cc 0.5 v i ik dc input diode current 20 ma i ok dc output diode current 50 ma i o dc output sink/source current 50 ma i cc dc supply current per output pin 50 ma i gnd dc ground current per output pin 50 ma t stg storage temperature range 65 to 150 c t l lead temperature, 1 mm from case for 10 seconds 260 c t j junction temperature under bias 150 c ja thermal resistance (note 2) soic tssop 125 170 c/w p d power dissipation in still air at 85 c soic tssop 125 170 mw msl moisture sensitivity level 1 f r flammability rating oxygen index: 30% ? 35% ul 94 v?0 @ 0.125 in v esd esd withstand voltage human body model (note 3) machine model (note 4) charged device model (note 5) > 2000 > 200 > 1000 v i latch?up latch?up performance above v cc and below gnd at 85 c (note 6) 100 ma stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. 1. i o absolute maximum rating must be observed. 2. the package thermal impedance is calculated in accordance with jesd51?7. 3. tested to eia/jesd22?a114?a. 4. tested to eia/jesd22?a115?a. 5. tested to jesd22?c101?a. 6. tested to eia/jesd78. recommended operating conditions symbol parameter min typ max unit v cc supply voltage MC74AC00 mc74act00 2.0 4.5 5.0 5.0 6.0 5.5 v v in , v out dc input voltage, output voltage (ref. to gnd) 0 ? v cc v t r , t f input rise and fall time (note 7) v cc @ 3.0 v MC74AC00 v cc @ 4.5 v v cc @ 5.5 v ? ? ? 150 40 25 ? ? ? ns/v t r , t f input rise and fall time (note 8) v cc @ 4.5 v mc74act00 v cc @ 5.5 v ? ? 10 8.0 ? ? ns/v t j junction temperature ? ? 150 c t a operating ambient temperature range ?55 25 125 c i oh output current ? high ? ? ?24 ma i ol output current ? low ? ? 24 ma functional operation above the stresses listed in the recommended operating ranges is not implied. extended exposure to stresse s beyond the recommended operating ranges limits may affect device reliability. 7. v in from 30% to 70% v cc . 8. v in from 0.8 v to 2.0 v.
MC74AC00, mc74act00 www. onsemi.com 3 dc characteristics symbo l parameter v cc (v) MC74AC00 unit conditions t a = +25 c t a = ?40 c to +85 c t a = ?55 c + 125 c typ guaranteed limits v ih minimum high level input voltage 3.0 4.5 5.5 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 2.1 3.15 3.85 v v out = 0.1 v or v cc ? 0.1 v v il maximum low level input voltage 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 0.9 1.35 1.65 v v out = 0.1 v or v cc ? 0.1 v v oh minimum high level output voltage 3.0 4.5 5.5 2.99 4.49 5.49 2.9 4.4 5.4 2.9 4.4 5.4 2.9 4.4 5.4 v i out = ?50 a 3.0 4.5 5.5 ? ? ? 2.56 3.86 4.86 2.46 3.76 4.76 2.4 3.7 4.7 v *v in = v il or v ih ?12 ma i oh ?24 ma ?24 ma v ol maximum low level output voltage 3.0 4.5 5.5 0.002 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 v i out = 50 a 3.0 4.5 5.5 ? ? ? 0.36 0.36 0.36 0.44 0.44 0.44 0.5 0.5 0.5 v *v in = v il or v ih 12 ma i ol 24 ma 24 ma i in maximum input leakage current 5.5 ? 0. 1 1.0 1.0 a v i = v cc , gnd i old ?minimum dynamic output current 5.5 ? ? 75 50 ma v old = 1.65 v max i ohd 5.5 ? ? ?75 ?50 ma v ohd = 3.85 v min i cc maximum quiescent supply current 5.5 ? 4.0 40 40 a v in = v cc or gnd product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. *all outputs loaded; thresholds on input associated with output under test. ?maximum test duration 2.0 ms, one output loaded at a time. note: i in and i cc @ 3.0 v are guaranteed to be less than or equal to the respective limit @ 5.5 v v cc . ac characteristics (t r = t f = 3.0 ns; c l = 50 pf; see figures 3 and 4 for waveforms) symbo l parameter v cc * (v) MC74AC00 unit t a = +25 c t a = ?40 c to +85 c t a = ?55 c to + 125 c min typ max min max min max t plh propagation delay 3.3 5.0 2.0 1.5 7.0 6.0 9.5 8.0 2.0 1.5 10.0 8.5 1.0 1.0 11.0 8.5 ns t phl propagation delay 3.3 5.0 1.5 1.5 5.5 4.5 8.0 6.5 1.0 1.0 8.5 7.0 1.0 1.0 9.0 7.0 ns *voltage range 3.3 v is 3.3 v 0.3 v. voltage range 5.0 v is 5.0 v 0.5 v.
MC74AC00, mc74act00 www. onsemi.com 4 dc characteristics symbo l parameter v cc (v) mc74act00 uni t conditions t a = +25 c t a = ?40 c to +85 c t a = ?55 c to + 125 c typ guaranteed limits v ih minimum high level input voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 2.0 2.0 v v out = 0.1 v or v cc ? 0.1 v v il maximum low level input voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 0.8 0.8 v v out = 0.1 v or v cc ? 0.1 v v oh minimum high level output voltage 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 4.4 5.4 v i out = ?50 a 4.5 5.5 ? ? 3.86 4.86 3.76 4.76 3.7 4.7 v *v in = v il or v ih i oh ?24 ma ?24 ma v ol maximum low level output voltage 4.5 5.5 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 v i out = 50 a 4.5 5.5 ? ? 0.36 0.36 0.44 0.44 0.5 0.5 v *v in = v il or v ih i ol 24 ma 24 ma i in maximum input leakage current 5.5 ? 0.1 1.0 1.0 a v i = v cc , gnd i cct additional max. i cc /input 5.5 0.6 ? 1.5 1.6 ma v i = v cc ? 2.1 v i old ?minimum dynamic output current 5.5 ? ? 75 50 ma v old = 1.65 v max i ohd 5.5 ? ? ?75 ?50 ma v ohd = 3.85 v min i cc maximum quiescent supply current 5.5 ? 4.0 40 40 a v in = v cc or gnd product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. *all outputs loaded; thresholds on input associated with output under test. ?maximum test duration 2.0 ms, one output loaded at a time. ac characteristics (t r = t f = 3.0 ns; c l = 50 pf; see figures 3 and 4 for waveforms) symbo l parameter v cc * (v) mc74act00 unit t a = +25 c t a = ?40 c to +85 c t a = ?55 c to +125 c min typ max min max min max t plh propagation delay 5.0 1.5 5.5 9.0 1.0 9.5 1.0 9.5 ns t phl propagation delay 5.0 1.5 4.0 7.0 1.0 8.0 1.0 8.0 ns *voltage range 5.0 v is 5.0 v 0.5 v. capacitance symbol parameter value typ test conditions unit c in input capacitance 4.5 v cc = 5.0 v pf c pd power dissipation capacitance 30 v cc = 5.0 v pf
MC74AC00, mc74act00 www. onsemi.com 5 figure 3. switching waveforms gnd v cc output y input a or b c l * *includes all probe and jig capacitance 50% device under test output figure 4. test circuit 90% v mi 10% t plh t phl t f t r 50 scope test point 450 input v mi = 50% for MC74AC00 = 1.5 v for mc74act00 order information device package shipping ? MC74AC00dg soic?14 (pb?free) 55 units / rail MC74AC00dr2g soic?14 (pb?free) 2500 / tape and reel MC74AC00dtr2g tssop?14 (pb?free) mc74act00dg soic?14 (pb?free) 55 units / rail mc74act00dr2g soic?14 (pb?free) 2500 / tape and reel mc74act00dtr2g tssop?14 (pb?free) ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
MC74AC00, mc74act00 www. onsemi.com 6 package dimensions soic?14 nb case 751a?03 issue k notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b does not include dambar protrusion. allowable protrusion shall be 0.13 total in excess of at maximum material condition. 4. dimensions d and e do not include mold protrusions. 5. maximum mold protrusion 0.15 per side. h 14 8 7 1 m 0.25 b m c h x 45 seating plane a1 a m s a m 0.25 b s c b 13x b a e d e detail a l a3 detail a dim min max min max inches millimeters d 8.55 8.75 0.337 0.344 e 3.80 4.00 0.150 0.157 a 1.35 1.75 0.054 0.068 b 0.35 0.49 0.014 0.019 l 0.40 1.25 0.016 0.049 e 1.27 bsc 0.050 bsc a3 0.19 0.25 0.008 0.010 a1 0.10 0.25 0.004 0.010 m 0 7 0 7 h 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.019 6.50 14x 0.58 14x 1.18 1.27 dimensions: millimeters 1 pitch soldering footprint* *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d.
MC74AC00, mc74act00 www. onsemi.com 7 package dimensions tssop?14 case 948g issue b dim min max min max inches millimeters a 4.90 5.10 0.193 0.200 b 4.30 4.50 0.169 0.177 c ??? 1.20 ??? 0.047 d 0.05 0.15 0.002 0.006 f 0.50 0.75 0.020 0.030 g 0.65 bsc 0.026 bsc h 0.50 0.60 0.020 0.024 j 0.09 0.20 0.004 0.008 j1 0.09 0.16 0.004 0.006 k 0.19 0.30 0.007 0.012 k1 0.19 0.25 0.007 0.010 l 6.40 bsc 0.252 bsc m 0 8 0 8 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a does not include mold flash, protrusions or gate burrs. mold flash or gate burrs shall not exceed 0.15 (0.006) per side. 4. dimension b does not include interlead flash or protrusion. interlead flash or protrusion shall not exceed 0.25 (0.010) per side. 5. dimension k does not include dambar protrusion. allowable dambar protrusion shall be 0.08 (0.003) total in excess of the k dimension at maximum material condition. 6. terminal numbers are shown for reference only. 7. dimension a and b are to be determined at datum plane ?w?. s u 0.15 (0.006) t 2x l/2 s u m 0.10 (0.004) v s t l ?u? seating plane 0.10 (0.004) ?t? ??? ??? 0.25 (0.010) 8 14 7 1 pin 1 ident. h g a d c b s u 0.15 (0.006) t ?v? 14x ref k n n 7.06 14x 0.36 14x 1.26 0.65 dimensions: millimeters 1 pitch soldering footprint* *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d.
MC74AC00, mc74act00 www. onsemi.com 8 p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 MC74AC00/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative on semiconductor and the are registered trademarks of semiconductor components industries, llc (scillc) or its subsidia ries in the united states and/or other countries. scillc owns the rights to a number of pa tents, trademarks, copyrights, trade secret s, and other intellectual property. a listin g of scillc?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent?marking.pdf. scillc reserves the right to make changes without further notice to any product s herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any part icular purpose, nor does sci llc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typi cal? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating param eters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgic al implant into the body, or other applications intended to s upport or sustain life, or for any other application in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer s hall indemnify and hold scillc and its officers , employees, subsidiaries, affiliates, and dist ributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufac ture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner.
|
